Included
any coating job
From
$0
to extra
- Diamond grinding
- Crack & joint repair
- Spalling patch as needed
- Built into coating price
Surface Prep & Repair · Hudson, WI · Est. 2003
Surface Prep & Repair in Hudson, Wisconsin.
Hudson sits on the Wisconsin side of the St. Croix River, directly across from Stillwater MN, and is the closest major town to the Twin Cities along I-94. About 25 minutes northwest of River Falls. We install polyurea + polyaspartic floor coatings for Hudson homeowners — diamond-ground prep, custom flake colors, 1–2 day install, written 15-year warranty. Wide range — historic Victorians and early-20th-century homes near downtown and North Hill, high-end St. Croix River-front estates, and post-1990 suburban developments on the east and south edges.
Surface Prep & Repair in Hudson
What an install looks like in Hudson.
Hudson has a different garage-floor profile than River Falls. The North Hill and downtown areas have older slabs from the 1920s-1960s that often need crack repair and spalling patch before coating — we handle that in prep. The high-end river-front and Willow River homes often have larger 3-car garages with custom flake color preferences. The post-1990 suburban developments south and east of town have newer slabs that grind cleanly. We've done installs near Birkmose Park, Stagecoach Trail, and along the lakefront. A common Hudson concern is lower-level moisture from St. Croix River proximity — we run an MVER test on every basement or walk-out garage install in town to make sure the slab is dry enough for a standard polyurea install.
Neighborhoods we work in
- North Hill (historic)
- Downtown waterfront
- Willow River
- South Hudson
- Stagecoach Trail
- Birkmose Park area
100%
Diamond grind
On every coating install
0
Acid etch
Ever, on any job
20+
Years experience
Surface prep since 2003
Always
Included
Not an upsell line item
Why we don't install epoxy in Hudson
Why diamond grinding is the only acceptable surface prep — and acid etching is not.
Surface prep is where cheap coating installs get cheap. Acid etching takes 30 minutes with a $40 jug of muriatic acid; diamond grinding takes hours with $30,000 worth of equipment. The cost difference is why some installers acid etch — and the bond difference is why those floors peel. Here's the head-to-head:
Acid Etching
What cheap installers do
- Doesn't open the slab uniformly. Acid reacts with the calcium in concrete unevenly — areas with more cement react more, areas with more aggregate react less. The surface profile after acid is inconsistent.
- Leaves chemical residue. Muriatic acid leaves chloride ions in the concrete pores. Coatings bonded over chloride residue have a weak chemical bond that fails sooner.
- Produces a chemical bond, not mechanical. The coating is essentially "glued" to the surface. Mechanical bonds (where the coating fuses into open pores) are dramatically stronger.
- Doesn't remove existing coatings. Old paint, sealers, or coatings have to come off some other way. Acid won't dissolve them. Many installers acid-etch over partial old coatings — guaranteed failure.
- Health + environmental concerns. Strong acid in residential garages and basements is unpleasant. The runoff has to go somewhere. Local code is increasingly restrictive on residential acid use.
Diamond Grinding
What we use
- Uniform surface profile. Diamond-tooled grinders cut the same depth across the entire slab regardless of cement-to-aggregate ratio. The surface profile after grinding meets ICRI CSP-3 to CSP-4 standards for coating bond.
- Removes contamination + weak top layer. Grinding cuts through the laitance (the weak, dust-prone top layer of cured concrete) and any surface contamination — oil, paint, sealers, coatings — in one pass. Clean substrate for the bond.
- Mechanical bond. The coating fuses into the open concrete pores, locking in. Mechanical bonds resist 4-10× the pull-off force of chemical bonds in published lab tests.
- Removes any existing coating. Old paint, epoxy, or sealer comes off cleanly. We grind down to bare concrete on every job.
- HEPA-vacuum dust collection. Industrial grinders with attached HEPA vacuums make zero dust mess in residential interiors. Garage, basement, mudroom — we can grind without making the rest of the house unlivable.
If a coating contractor offers to "save you money on prep" by acid-etching, that's the moment to walk away. The prep is the foundation of the install — saving 30 minutes on prep guarantees a re-install in 18 months. Diamond grinding is the only surface prep we do, and it's included in every coating price.
Hudson Pricing
Surface Prep & Repair cost in Hudson, WI: $7–9 per sq ft.
For a coating install, prep is included in the per-sq-ft coating price — never a separate line item, never an upsell. For standalone prep work (sub-contracting to another coating contractor or repair-only jobs), pricing depends on slab condition + scope.
Standalone
any sq ft
From
$2
to $4 / sq ft
- Diamond grinding only or full prep
- Coordinate with coating contractor
- Documented surface profile
- Larger jobs price lower per sq ft
Bid by scope
linear ft + sq ft
From
Quote
to by Dave
- Crack filling (per linear foot)
- Spall + pit repair (per sq ft)
- No coating
- Stopgap before future install
Standalone prep is typically a contractor-to-contractor arrangement, but homeowners with damaged slabs sometimes commission repair-only work as a stopgap before a future coating install. Send photos + scope and Dave will quote.
The 6-step install
How we install your floor in Hudson.
Same checklist on every floor. The reason our coatings still look new at year ten when the cheap stuff peeled in year two.
-
01
Assess slab condition
On-site visit to evaluate slab condition: existing coatings, cracks, spalling, oil contamination, moisture indicators. Determines scope of prep work needed and which grind tooling to use (concrete hardness varies, tooling matches). -
02
Diamond grinding (full slab)
Industrial diamond-tooled grinders, HEPA-vacuum dust collection, ICRI CSP-3 to CSP-4 surface profile. Wall-to-wall, edge-to-edge, including corners and tight spots. Removes existing coatings, contamination, and the weak laitance layer. -
03
Crack & joint repair
Visible cracks filled with flexible polyurea joint filler that moves with the slab. Control joints either filled flush (smooth surface) or maintained as visible (homeowner preference). Edge cracks at the slab perimeter sealed. -
04
Spalling + pitting repair
Spalled surface areas patched with polymer-modified concrete repair compound, troweled flat to match surrounding surface. Pits filled and smoothed. Compound cures overnight, ready for coating the next day. -
05
Surface clean + final inspection
Full vacuum sweep + tack-cloth wipe to remove residual dust before coating goes down. Walk-through with homeowner to confirm prep is complete and sign off before basecoat. -
06
Documented + warrantied
For standalone prep work, we document surface profile (CSP rating) and crack repair scope so the coating contractor has a record. For our own coating installs, the prep is integrated into the 15-year coating warranty — bond failure due to inadequate prep is on us, not you.
Hudson questions
Common questions for Hudson homeowners.
Do you install in the historic homes on North Hill?
Yes — those are some of our most rewarding jobs. Older slabs need more prep (diamond grinding to remove old paint, crack repair for settlement, spalling patch) but the polyurea system bonds reliably to a properly prepped substrate. We've done garages built in the 1930s that look brand new after coating.
What about basement coatings near the St. Croix River — is moisture a concern?
Lower-level slabs in Hudson can transmit slightly more moisture than inland sites. We run an MVER (moisture vapor emission) test before coating any below-grade surface in Hudson. Most slabs clear for a standard install; some get a moisture-mitigation primer first. Either way you know up-front what your slab needs.
How fast can you get to Hudson from River Falls?
About 25 minutes via I-94. We typically schedule Hudson installs in the same week as a River Falls job to amortize travel. Same-day photo quotes are normal — Dave will text back a real number after seeing four photos of your slab.
Why does my floor coating keep peeling?
Almost always inadequate surface prep. The most common cause is acid etching instead of diamond grinding — the chemical bond is dramatically weaker and fails first under thermal cycling, moisture, or load. Other causes: coating applied over old coating without grinding it off, moisture transmission from below (untested), or hot-tire pickup damage on epoxy. If a previous floor coating peeled within a few years, the next one needs to be installed differently — start with full diamond grinding to remove whatever's left, then a polyurea (not epoxy) system on top.
What's the difference between diamond grinding and acid etching?
Diamond grinding mechanically cuts the concrete surface with diamond-tooled abrasives, opening the pores uniformly and creating a mechanical bond profile (ICRI CSP-3 to CSP-4). Acid etching uses muriatic acid to chemically react with the surface — uneven, leaves chloride residue in the pores, creates a weaker chemical bond. Lab pull-off tests show diamond-ground surfaces hold coatings at 4-10× the bond strength of acid-etched surfaces. We never acid etch.
Is surface prep included in the coating price?
Yes — diamond grinding, crack repair, and spalling patch are included in every coating install we do. It's not a separate line item or upsell. The 15-year warranty exists because the prep underneath it is right; charging extra for prep would be charging extra for the foundation of the install.
Do you do standalone surface prep without a coating?
Yes — for two cases: (1) sub-contracting to another coating contractor whose own crew doesn't have grinder equipment, and (2) repair-only work for homeowners with cracks or spalling that need fixing but who aren't ready for a full coating yet. Standalone prep runs $2-4 per square foot depending on slab condition and scope; repair-only is bid by scope.
How long does the diamond grinding take?
For a typical 2-car garage (~440 sq ft), grinding runs 2-3 hours including setup, wall-to-wall coverage, and cleanup. Larger spaces scale linearly. Crack repair adds 30-60 minutes depending on linear footage. Spalling repair adds 1-2 hours per 100 sq ft of repair area. The dust is contained by HEPA vacuum so the rest of your house stays livable during grinding.
Will the dust from grinding be a problem?
No — our grinders run with attached HEPA-vacuum dust collection. Effectively zero airborne dust escapes during grinding. We can grind in residential garages, basements, and mudrooms without affecting other parts of the house. After grinding we vacuum the slab a final time before any coating goes down.
What if my slab has cracks — can it still be coated?
Almost always yes. Cracks get filled with flexible polyurea joint filler before the coating goes down. The filler bonds to both sides of the crack and stretches with future movement, so the crack doesn't telegraph back through the coating. Exceptions: structural cracks (deep, through-slab, or growing) are signs of a foundation issue that should be addressed before coating. We'll tell you on-site.
What about old paint or sealer on the floor?
Diamond grinding removes most old paint, sealers, and coatings cleanly in one pass. Stubborn cases (heavy enamel paint, deeply penetrating sealers) get an extra grind pass or a chemical degrease step before grinding. By the time the new coating goes down, the slab is bare concrete substrate.
Do you handle severely spalled or damaged concrete?
Most spalling, pitting, and minor surface damage is repairable with polymer-modified concrete compound, troweled flat, and overcoated. Severely damaged concrete (large sections lifted from frost heave, structural cracks, deep through-slab damage) is sometimes beyond restoration — a coating over a structurally bad slab buys 1-2 years before the underlying problem reappears. We'll tell you straight if your slab needs replacement instead of restoration.
Why do you test for moisture before coating below-grade?
Below-grade slabs (basements, walk-outs, lower-level garages) transmit ground moisture upward through the concrete. High moisture causes coating delamination — the bond between coating and slab fails as moisture vapor builds up underneath. We run an MVER test before coating any below-grade surface; readings tell us whether the slab is dry enough for a standard install or needs a moisture-mitigation primer underneath. Avoids the most common cause of below-grade coating failure.
More in Hudson
All the floor coatings we install in Hudson, WI.
Whatever the slab — garage, basement, patio, mudroom, commercial — same diamond-ground prep, same polyurea + polyaspartic system, same 15-year warranty. Bundle pricing if you book multiple rooms in one visit.
Talk to Dave
Ready for a surface prep & repair install in Hudson?
Send Dave four photos of your slab — he'll text back a real Hudson number same-day. No salesperson, no quote-bot, no follow-up calls.
- Free on-site measurement in Hudson
- Written 15-year warranty
- No subcontractors, no upsells